![]() ![]() Route planning Google Earth, GaiaGPS, topo maps and more.Navigation with Gaia GPS Smartphone navigation.Start and End at Home Online trip-planning course: Jan-March 2022!.Archived workshops Tech tools for remote overland travel.Mind & Mountain My wife Sarah’s awesome fitness programs: Ski Babes and Summer Strong.“Start and End at Home” Online trip and emergency planning course.“Paddle Up a Level” Online packrafting course.Packraft instruction Safety, rescue, and river running.Courses Ice and river safety and rescue Trip & emergency planning.Get the newsletter! Stories, safety, and stewardship.Also, skiers who have experienced problems with tele binding pull out should consider the Binding Freedom inserts option for creating a bomber mount. It’s worth having a few in your ski bench kit just for that reason. I had a little trouble with the insert installer tool, but SVST has since revamped the tool (as of 1/1/15) for better fit tolerance and is using higher grade hardened steel, so make sure you get the new one.Īnother potentially excellent use for these inserts is for hole repair on any binding mount. In other words, be careful to double check everything and move slowly. It can certainly be done, but paper jigs require another degree of measure-twice-cut-once attention to detail. The project gets a little bigger if you are drilling the skis for the first time and are using paper jigs. It’s not rocket science, but it does require careful, methodical work and experience with tools. I’ll emphasize, though, that if you’re not a tinkerer or a DIY binding person, you should think twice about doing this yourself. A countersink bit is helpful for the deburring too. There’s definitely a learning curve, but the tips to dry-fit, clean and deburr the holes will help keep the install smooth. I’ve mounted a lot of skis over the years but have never installed inserts before. Let cure, sand any excess epoxy on top sheet and mount bindings using new machine screws and a threadlock compound like Vibratite. Install each insert with epoxy (24-hour cure – not 5-minute) using the special insert installation tool being sure to run the inserts down flush with the ski’s topsheet.Ħ. Dry-fit each insert to test the depth and fit – sounds tedious but makes a difference and only adds five minutes per ski to the process.ĥ. Tap each hole by hand – the basic tap handle works great for this, but take your time and make sure you run it straight.Ĥ. But you can also do it with a sharp utility knife.ģ. Clean and deburr each hole – this helps reduce volcanoing around the hole and helps keep the inserts easy to flush mount.I recommend spending the extra $19 on the deburring tool if you don’t have one. If your ski is already drilled for one binding, you can simply re-drill the existing holes with the insert bit – that’s what I did and it worked great.Ģ. This is done with the special insert bit that drills a hole to accommodate the insert. Drill the ski for the appropriate binding mounting patterns. These paper binding jigs are key if you need to drill the ski for the first time for one or both of the bindings.ġ. They also have an impressive variety of paper jigs for just about every ski binding available for download on their website. The helpful folks at SVST have it all lined out for ya. Binding Freedom is now part of Sun Valley Ski Tools (SVST) and you get all of the tools and parts required for the process through SVST. The inserts themselves are all the same, but you must specify your binding models, so you get the proper length and head style on the screws that thread into the inserts. I chose a pair of skis that had already had both Markers and Dynafits installed at one point in their life, so all I needed to do was redrill the two different binding patterns with the special insert-sized bit (6.5mm) and then follow the straightforward insert installation process. It’s a cleaner and lighter system than using plates, though it does require a fair number of holes to be drilled if your setting up one ski for two bindings. Of course, you could have a qualified shop do it, but by its very nature, it seems like it’s gonna appeal to the DIY crowd. Once installed, it’s like the inserts on a snowboard. This means you install threaded inserts in your ski to match the bindings you wish to swap. Originally a plate-based system, where you mounted a machined plate to your ski that allowed binding swaps, Binding Freedom has evolved to become binding-insert-based. I recently installed a set of Binding Freedom inserts to accommodate Marker Tours and Dynafit Radicals on a set of skis. There are a couple of solutions available for skiers looking to swap between two sets of bindings on a single pair of skis or use one set of bindings on two pairs of skis, Binding Freedom and Quiver Killers. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |